TGX10
Dsp power amplifier 4 x 2500w, live
4-channel DSP amplifier for live applications
Power density of up to 10kW in 2RU
Fully integrated DSP with advanced 96 kHz processing and FIR Drive technology
OMNEO integration for seamless compatibility with Dante and OCA
Full color touch screen for control without software
Specifications
OUTPUT POWER
Load impedance
2 Ω
2.7 Ω
4 Ω
8 Ω
Maximum Output Power1 All channels driven
2600 W
3000 W
2500 W
1250 W
Number of amplifier channels
4
Specifications
Maximum Output Voltage
150 V peak
Maximum Output Current
53 A peak
AMPLIFIER
Voltage Gain ref.1 kHz
32.0 dB, adjustable 24-40 dB
Input Sensitivity ref. to Max. Output Voltage
10.7 dBu (2.66 V), adjustable 2.7-18.7 dBu
THD 3 dB below Max., AES17, 1 kHz
< 0.05 %
IMD-SMPTE, 60 Hz, 7 kHz
< 0.05 %
DIM100, 3.15 kHz, 15 kHz
< 0.15 %
Crosstalk ref. 1 kHz, 12 dB below Max., 8 Ω
< -80 dB
Frequency Response ref. 1 kHz, analog in to speaker out
20 Hz to 20 kHz (ą0.5 dB)
Damping Factor, 20 Hz to 200 Hz, 8 Ω
> 400
Output Stage Topology
Class D, fixed frequency
Signal to Noise Ratio
A-weighted, analog input
112 dB
A-weighted, digital input
115 dB
Output Noise
A-weighted, analog input
< -70 dBu
A-weighted, digital input
< -73 dBu
DIGITAL SIGNAL PROCESSING
Sampling rate
48 kHz/96 kHz, OMNEO/Dante synchronized
Signal Delay/Latency
Analog in to Speaker Out, 48 kHz/96 kHz
0.70 ms/0.53 ms
AES3 in to Speaker Out, 48 kHz/96 kHz
1.00 ms/0.66 ms
Dante Network Latency
typ. 1.00 ms
Signal Processing
32/40 bit, floating point
User EQ
12 filters per channel, selectable as PEQ, Lo-Shelv, Hi-Shelv, Lo-ShelvQ, Hi-ShelvQ, Hi-Pass, Lo-Pass & Notch; 2 filters of them withadditional asymmetric filter type
User Delay
0 to 2000 ms per channel (units: μs, ms, s, cm, m, inches, feet)
Array EQ
5 filters per channel, selectable as PEQ, Lo-Shelv, Hi-Shelv, Lo-ShelvQ, Hi-ShelvQ, Hi-Pass, Lo-Pass, & All-Pass
Array Delay
0 to 500 ms per channel (units: μs, ms, s, cm, m, inches, feet)
Speaker EQ
10 filters per channel, selectable as PEQ, Lo-Shelv, Hi-Shelv, Hi-Pass, Lo-Pass, & All-Pass
Speaker X-Over
Hi-Pass & Lo-Pass per channel, 6/12/18/24/30/36/42/48 dB Bessel/Butterworth, 12/24/48 dB Linkwitz-Riley; Alignment Delay, 0 to 20 ms per channel
Speaker FIR
up to 1025 taps, Linear Phase Filter, Linear Phase Brickwall X-Over
Speaker Limiters
Peak Anticipation Limiter & RMS/TEMP Limiter per channel
Other functions
Source Selection & Mix, Level, Mute, Polarity, Sine & Noise Generator, Level Meters, Impedance Measurement, & Load Monitoring
Memory
DSP Presets
1 Factory + 20 User
Speaker-Pool Presets
30 speaker settings
Source Supervision & Fallback
AES3 Lock & OMNEO/Dante network supervision, switchover to alternative Source Selection
CONNECTIVITY
Analog Audio Input/Thru
Type
AES3 Lock & OMNEO/Dante network supervision, switchover to alternative Source Selection
Maximum Input Level
+24 dBu
Input Impedance, active balanced
20 kΩ
Reference level equal to digital input
+21 dBu for 0 dBFS
Digital Audio Input/Thru
Type
2 x 3-pin XLR (alternative use of Analog In/Thru)
Format
AES3 (AES/EBU)
Input Sample Rates
32 to 192 kHz, internal Sample-Rate-Converter
Thru Connector
active buffered, direct bypass if device is unpowered
Network
Type
2 x Neutrik etherCON/RJ45, redundant PRIMARY/SECONDARY
Format
1000base-T/100base-TX, integrated switch
Network Audio Inputs
8 channels, 48/96 kHz, OMNEO/Dante format
Network Audio Outputs (Monitor)
2 channels, 48/96 kHz, OMNEO/Dante format
Front side Service Port
1 x USB Type A
Mains Input
1 x Neutrik powerCON-HC
Speaker Output
4 x NL4
GENERAL
User Interface
Display
320 x 240 pixel, 3.5" color TFT"
Front panel indicators
Full color LED illuminated ring
Front panel operating elements
Rotary encoder, Capacitive Touch Screen
Rear panel indicators
2 x LED (AES3 Input mode active, Amp-Find)
Rear panel operating elements
Mains switch
Power Requirements
100 V to 240 V, 50 Hz to 60 Hz AC
Power Consumption
Rated Power Consumption
1200 W
⅛ Maximum Output Power at 4 Ω
1765 W
Idle Mode (no input signal)
80 W
Standby Mode
< 18 W
Power Supply Topology
Switching Mode Power Supply with digital controlled Power Factor Correction
Protections
Audio Limiters, High Temperature, DC, HF, Short Circuit, Back-EMF, Peak Current Limiters, Inrush Current Limiters, Turn-on Delay, Mains Circuit Breaker Protection, Mains Over/ Under voltage Protection
Cooling:
Front-to-rear, temperature controlled fans, supervised
Ambient Temperature Limits
+5 °C to +40 °C (+40 °F to +105 °F)
IEC Protection Class
Class I (grounded)
Electromagnetical Environment
E1, E2, E3
Color
Black
Dimensions (W x H x D), mm
483 x 88.1 x 514.2
Weight
15.0 kg (33.0 lb)
Shipping Weight
17.2 kg (37.8 lb)
Amplifier at rated conditions; all channels driven, 4 Ω loads, analog input, 32 dB gain, 48 kHz sample rate, unless otherwise specified.
1Test signal for max. output power according IHFA-202 (ynamic-Headroom, burst 1 kHz/20 ms on/480 ms off/low level -20 dB).
Similar Products |
|